Alan W2AEW Sr. Field Applications Engineer

The DMM353 was only produced for about a year (1995-1996).  It is quite likely that an electronic (PDF) copy of the manual was never produced.

The Video trigger requires an analog source, as you know.  I have not been able to duplicate this issue.  If I start with a default setup, and change the Edge trigger source to D0, and then rotate the trigger type to Video, the Source changes to the highest analog channel number (4).  I am running 1.30 on an MDO3104.

Hi John,<br> <br> This most often happens when the system detects some tampering with the licensing system, or if the firmware is down-graded below v3.3.&#160; Other causes could be due to some hardware failure.&#160; In all cases however, the unit will need to be serviced by Tektronix to restore the serial number and licenses.

The 2432A is a 300MHz scope, so it is quite normal to have some noise on the trace with nothing connected at the input.  Since this scope features a digitizer to sample the waveform, the noise appears more apparent than it would from just a live analog trace where the noise would appear muted due to the phosphor glowing brighter in the middle of the trace.

The THD measurement can be made on audio signals - either directly (baseband), or as demodulated from an AM or FM modulated carrier.  The measurement can be performed on audio frequencies from 20Hz to 100kHz.

This should get you started:

To add the measurement, use MEASU:MEASn:Type phase, where n is the measurement number (assuming you have more than one measurement defined)
To configure the sources, use MEASU:MEASn:SOURCEx CHy, where x is 1 or 2, to define the two sources for the Phase measurement, and y is the channel number you're setting to a given source.
For example:
MEASUrement:MEAS1:TYPE phase 
adds the Phase measurement badge as measurement 1
MEASUrement:MEAS1:SOUrce1 CH2
MEASUrement:MEAS1:SOUrce2 CH3
sets CH2 as the first source and CH3 as the second source for the Phase measurement.

To read the current mean value of the measurement:
MEASUrement:MEAS1:RESUlts:CURRentacq:MEAN?

Channel labels applied via the Channel Badge will always be lined up with the Channel Handles, whether an offset is used or not.  If you prefer to have a label that is not lined up with the channel handle, you can use the "Callout" feature (button on the upper right corner of the display).  You can add an unlimited number of Callouts.  There are four different types of callouts:  

• Note: simple on-screen text
• Arrow: on-screen text with an arrow you can use to point at something
• Rectangle:  on-screen text with a user-sizable/moveable rectangle
• Bookmark: on-screen text *and* a probe-point that you can position on a trace for an instant readout

The format of the text, including font, size, and color, is all user adjustable.  Callouts can be placed anywhere on the screen.

This can be done using the Burst Mode on each channel.  With the sine frequency of 27kHz, if you set the number of cycles in the Burst Mode to be 270,000 then the burst duration will be 10 seconds.  You then set the Trigger Interval to 20 seconds, and you'll get the 10 seconds "on" and 10 seconds "off".  Do the same for the second channel, but set the delay to 10 seconds. This will cause the 2nd channel to come on when the first channel turns off.

Unfortunately, there isn't a way of easily changing the amplitude on consecutive bursts.  You can do this manually (adjust CH1 while CH2 is playing, and vice versa), or programmatically.

You may want to check with the fine folks at VintageTEK.org.  They may have the firmware images for the 11302.

On the 4/5/6 Series scopes, the measurement system does keep the statistics of consecutive acquisitions (provided no configuration changes were made between acquisitions).  To see the accumulated statistics, simply add a Measurement Results Table.  You can do this by clicking/tapping the "Results Table" on-screen button in the upper right corner of the display, and then selecting Measurements.  On the result table, there will be two sets of statistical data (mean, min, max, stddev, population). The set to the left are the "local" stats, which are updated with each acquisition.  The set to the right are the running accumulated statistics.